2010 Cadillac Truck SRX AWD V6-3.0L Page 1067

2010 Cadillac Truck SRX AWD V6-3.0L Page 1067

Conditions for Setting the DTC

P0030, P0036, P0050, or P0056

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 5 s.

P0053, P0054, P0059, or P0060

The ECM detects the HO2S heater is not within a specified resistance range at engine start-up.

P0135 or P0155

The ECM detects that the HO2S 1 heater current is greater than 3.1 amps, or less than 0.3 amps for greater than 8 s.

P0141 or P0161

The ECM detects that the HO2S 2 heater current is greater than 2.9 amps, or less than 0.3 amps for greater than 8 s.

Action Taken When the DTC Sets

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, command the appropriate B52 HO2S heater ON and OFF with a scan tool while observing the B52 HO2S Heater Circuit Test

Status parameter. The parameter should display OK or Not Run.

2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.2-1.5 A.

3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan

tool. The parameter should not change with movement.

瀚慖f movement affects the parameter, repair the appropriate harness or connector.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

2010 Cadillac Truck SRX AWD V6-3.0L Page 537

2010 Cadillac Truck SRX AWD V6-3.0L Page 537

Conditions for Setting the DTC

B2425 0D or B2430 0D

By measuring current and voltage output to the seat heating elements every 10 seconds, the rear seat heating control module calculates that the

heating element resistance is above the maximum resistance.

B2425 0B, B2425 0E, B2430 0B, or B2430 0E

By measuring current and voltage output to the seat heating elements every 10 seconds, the rear seat heating control module calculates that the

heating element resistance is below the minimum resistance.

Action Taken When the DTC Sets

The heated seat function for the affected seat will be disabled.

Conditions for Clearing the DTC

* The current DTC clears when the malfunction is no longer present, and the power mode changes to OFF then back to ACC or RUN.

* The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Heated/Cooled Seat Schematics (See: Body and Frame/Seats/Seat Temperature Element/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Rear Heated Seats Description and Operation (See: Body and Frame/Seats/Seat Temperature Element/Description and Operation/Rear Heated

Seats)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

B2425 0B, B2425 0D, or B2425 0E

1. Ignition OFF, disconnect the harness connector at the E14E seat back heating element.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

2. Test for 0.5 - 5 Ohms between terminal A and terminal B.

瀚慖f not within the specified range, replace the E14E seat back heating element.

3. Connect the harness connector at the E14E seat back heating element and disconnect the X2 harness connector at the K29R rear seat heating

control module.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

4. Test for 1 - 7 Ohms between control circuit terminal 3 and control circuit terminal 1.

瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14F seat cushion

2010 Cadillac Truck SRX AWD V6-3.0L Page 259

2010 Cadillac Truck SRX AWD V6-3.0L Page 259

Conditions for Setting the DTC

B242A 01

The seat heating control module detects a short to voltage on the heater element control circuits.

B242A 02

The seat heating control module detects a short to ground on the heater element control circuits.

Action Taken When the DTC Sets

The heated seat function for both seats will be disabled.

Conditions for Clearing the DTC

* The current DTC will clear and set a history code 3 seconds after the reference voltage returns to normal operating range and the ignition is

cycled OFF then back to ACC or RUN.

* The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Heated/Cooled Seat Schematics (See: Body and Frame/Seats/Seat Temperature Element/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Heated/Vented Seat Description and Operation (See: Body and Frame/Seats/Seat Temperature Element/Description and Operation/Heated/Vented

Seat)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the X2 harness connector at the K29 seat heating control module.

2. Test for infinite resistance between the control circuit terminal 3 and ground.

瀚慖f not the specified value, test the control circuit for a short to ground.

3. Test for infinite resistance between the control circuit terminal 5 and ground.

瀚慖f not the specified value, test the control circuit for a short to ground.

4. Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 3 and ground.

瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.

5. Verify that a test lamp does not illuminate between the control circuit terminal 5 and ground.

瀚慖f the test lamp illuminates, test the control circuit for a short to voltage.

6. If all circuits test normal, replace the K29 seat heating control module.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1457

2010 Cadillac Truck SRX AWD V6-3.0L Page 1457

Conditions for Setting the DTC

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 5 s.

Action Taken When the DTC Sets

DTCs P0351-P0356 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0351-P0356 are Type B DTCs.

Diagnostic Aids

A high resistance condition on any ignition control circuit can cause an engine misfire without setting DTC P0351-P0356.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic

Ignition System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine running, observe the following scan tool control circuit status parameters for the appropriate cylinder T8 ignition coil:

* Ignition Coil 1-6 Control Circuit Low Voltage Test Status

* Ignition Coil 1-6 Control Circuit Open Test Status

* Ignition Coil 1-6 Control Circuit High Voltage Test Status

Each parameter should display Not Run or OK.

2. Engine idling, observe the DTC information with a scan tool. DTC P0351, P0352, P0353, P0354, P0355, or P0356 should not set.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the appropriate T8 ignition coil.

2. Ignition OFF, and all vehicle systems OFF, it may take up to 2 minutes for all the systems to power down. Test for less than 5 ohm between

the ground circuit terminal A and ground.

瀚慖f greater than the specified range, repair the ground circuit for an open/high resistance.

3. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal B and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.

4. Ignition ON, verify that a test lamp illuminates between the ignition voltage circuit terminal D and ground.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1001

2010 Cadillac Truck SRX AWD V6-3.0L Page 1001

Conditions for Setting the DTC

The ECM detects that the voltage on the fuel economy mode switch signal wire is either too low or too high out of range.

Action Taken When the DTC Sets

DTCs P159F and P15A0 are Type B DTCs

Conditions for Clearing the MIL/DTC

DTCs P159F and P15A0 are Type B DTCs

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster is not illuminated.

2. Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster illuminates when the fuel economy mode switch

button is pressed.

3. Engine running, observe the scan tool DTC information. DTCs P159F and P15A0 should not set.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

1. Ignition OFF, disconnect the harness connector at the S87 fuel economy mode switch.

Note: It may take up to 2 minutes for all vehicle systems to power down.

2. Ignition OFF and all vehicle systems OFF, test for less than 5 ohm between ground circuit terminal 2 of the harness connector and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance and repair as necessary.

3. Ignition ON, test for 4.8-5.2 V between 5 V reference circuit terminal 9 of the harness connector and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition ON, test for 0.060-0.250 V between signal circuit terminal 10 of the harness connector and ground.

瀚慖f less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace

2010 Cadillac Truck SRX AWD V6-3.0L Page 872

2010 Cadillac Truck SRX AWD V6-3.0L Page 872

Conditions for Setting the DTC

The body control module (BCM) has not undergone the tire pressure sensor learn procedure.

Action Taken When the DTC Sets

* The tire pressure monitor indicator icon on the instrument panel cluster (IPC) will flash for 1 minute and then remain illuminated after the

ignition switch is cycled ON and the IPC bulb check is complete.

* If equipped, the driver information center (DIC) displays a service tire monitor type warning message.

Conditions for Clearing the DTC

A current DTC will clear when the BCM has undergone the tire pressure sensor learn procedure and 1 ignition cycle has occurred.

Reference Information

Description and Operation

Tire Pressure Monitor Description and Operation (See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Description

and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Special Tools

J-46079 Tire Pressure Monitor Diagnostic Tool

Circuit/System Verification

Verify that the DTC C0775 is not set.

If the DTC is set, perform the tire pressure sensor learn procedure. Cycle the ignition. If the DTC resets, replace the K9 BCM.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Tire Pressure Indicator Sensor Learn (See: Instrument Panel, Gauges and Warning Indicators/Tire Monitoring System/Tire Pressure

Sensor/Testing and Inspection)

* Control Module References (See: Testing and Inspection/Programming and Relearning)for BCM replacement, setup and programming.

C0800

DTC C0800

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC C0800 03

- Device Power 1 Circuit Voltage Below Threshold

2010 Cadillac Truck SRX AWD V6-3.0L Page 1218

2010 Cadillac Truck SRX AWD V6-3.0L Page 1218

Conditions for Setting the DTC

P0030, P0036, P0050, or P0056

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 5 s.

P0053, P0054, P0059, or P0060

The ECM detects the HO2S heater is not within a specified resistance range at engine start-up.

P0135 or P0155

The ECM detects that the HO2S 1 heater current is greater than 3.1 amps, or less than 0.3 amps for greater than 8 s.

P0141 or P0161

The ECM detects that the HO2S 2 heater current is greater than 2.9 amps, or less than 0.3 amps for greater than 8 s.

Action Taken When the DTC Sets

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, command the appropriate B52 HO2S heater ON and OFF with a scan tool while observing the B52 HO2S Heater Circuit Test

Status parameter. The parameter should display OK or Not Run.

2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.2-1.5 A.

3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan

tool. The parameter should not change with movement.

瀚慖f movement affects the parameter, repair the appropriate harness or connector.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

2010 Cadillac Truck SRX AWD V6-3.0L Page 423

2010 Cadillac Truck SRX AWD V6-3.0L Page 423

Conditions for Setting the DTC

The module has detected an internal malfunction.

Action Taken When the DTC Sets

The module refuses all additional inputs.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Diagnostic Aids

* This DTC may be stored as a history DTC without affecting the operation of the module.

* If stored only as a history DTC and not retrieved as a current DTC, do not replace the module.

* If this DTC is retrieved as both a current and history DTC, replace the module that set the DTC.

Circuit/System Verification

If this DTC is retrieved as a current DTC, replace the module that set the DTC.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

Control Module References (See: Testing and Inspection/Programming and Relearning) for module replacement, setup, and programming

Data Communications

DTC B1001

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptor

DTC B1001 XX

- Option Configuration

Circuit/System Description

Some control modules must be configured with serial numbers, vehicle options, or other information. If a control module was not properly

configured after installation that module may set DTC B1001. The symptom byte listed in the DTC Descriptor is for engineering reference only. No

external circuit diagnosis is involved.

Conditions for Running the DTC

Battery voltage is between 9-16 V and data link communications operate normally.

Conditions for Setting the DTC

The control module is not configured properly.

Conditions for Clearing the DTC

* A current DTC clears when the malfunction is no longer present.

* A history DTC clears when the module ignition cycle counter reaches the reset threshold, without a repeat of the malfunction.

2010 Cadillac Truck SRX AWD V6-3.0L Page 446

2010 Cadillac Truck SRX AWD V6-3.0L Page 446

Conditions for Setting the DTC

The DTC will set when the radio detects a short to voltage, short to ground, or an open/high resistance in the video display brightness control

circuit 400 ms after the radio activates the remote enable circuit.

Action Taken When the DTC Sets

The radio sets the DTC and defaults the video display to full brightness.

Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.

* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information

Schematic Reference

Video System Schematics (See: Accessories and Optional Equipment/Diagrams/Electrical Diagrams/Video System Schematics)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Video Entertainment System Description and Operation (Non-Headrest DVD Systems) (See: Accessories and Optional Equipment/Description

and Operation/Video Entertainment System (Non-Headrest DVD Systems))Video Entertainment System Description and Operation (Dual Headrest

DVD Systems) (See: Accessories and Optional Equipment/Description and Operation/Video Entertainment System (Dual Headrest DVD

Systems))Video Entertainment System Description and Operation (Seatback Display) (See: Accessories and Optional Equipment/Description and

Operation/Video Entertainment System (Seatback Display))

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Ignition ON, Radio ON, DVD playing, use the infrared remote control to change the brightness level of the seatback video displays.

瀚慖f one of both of the seatback video displays brightness level cannot be controlled, refer to Circuit/System Testing.

2. Verify that DTC B1289 is NOT set as current.

瀚慖f DTC B1289 is set as current, refer to Circuit/System Testing.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connectors at both of the P22 seatback video displays.

2. Ignition ON, DVD playing, test for 190-210 HZ DC between the video brightness control circuit terminal 16 and ground at each of the P22

seatback video displays.

瀚慖f not within the specified range, test the control circuit for a short to voltage, short to ground, or an open/high resistance. If the circuit

tests normal, replace the radio.

3. Ignition OFF, reconnect the harness connector at the P22E driver seatback video display.

4. Ignition ON, DVD playing, test for 190-210 HZ DC between the video brightness control circuit terminal 16 and ground at the P22F

passenger seatback video display.

瀚慖f not within the specified range, replace the P22E driver seatback video display.

5. If all circuits test normal, replace the P22F passenger seatback video display.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1049

2010 Cadillac Truck SRX AWD V6-3.0L Page 1049

Conditions for Setting the DTC

P0030, P0036, P0050, or P0056

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 5 s.

P0053, P0054, P0059, or P0060

The ECM detects the HO2S heater is not within a specified resistance range at engine start-up.

P0135 or P0155

The ECM detects that the HO2S 1 heater current is greater than 3.1 amps, or less than 0.3 amps for greater than 8 s.

P0141 or P0161

The ECM detects that the HO2S 2 heater current is greater than 2.9 amps, or less than 0.3 amps for greater than 8 s.

Action Taken When the DTC Sets

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, command the appropriate B52 HO2S heater ON and OFF with a scan tool while observing the B52 HO2S Heater Circuit Test

Status parameter. The parameter should display OK or Not Run.

2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.2-1.5 A.

3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan

tool. The parameter should not change with movement.

瀚慖f movement affects the parameter, repair the appropriate harness or connector.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

2010 Cadillac Truck SRX AWD V6-3.0L Page 410

2010 Cadillac Truck SRX AWD V6-3.0L Page 410

Conditions for Setting the DTC

B0958 01, B0959 01, B0960 01, or B0961 01

The parking assist control module has detected the voltage at the sensor circuit is greater than 11.5 V or the object sensor is not grounded.

B0958 06, B0959 06, B0960 06, or B0961 06

The parking assist control module has detected the voltage at the sensor circuit less than 0.5 V.

B0958 08, B0959 08, B0960 08, or B0961 08

The parking assist control module has received an invalid signal.

B0958 21, B0959 21, B0960 21, or B0961 21

The object sensor determines no change in the position of an object while the vehicle is in motion.

B0958 3A, B0959 3A, B0960 3A, or B0961 3A

The parking assist control module determines the wrong sensor type is installed.

Action Taken When the DTC Sets

^ The parking assist is disabled.

^ The driver information center displays SERVICE PARK ASSIST.

Conditions for Clearing the DTC

The condition for setting the DTC is no longer present.

Diagnostic Aids

For symptom byte 21 the module only runs diagnostic when the vehicle is driven greater than 40 km/h (25 MPH). Therefore, even with clean

sensor with no obstruction (i.e snow or ice melted off) drive the vehicle greater than 40 km/h (25 MPH).

The following is a list of reasons this failure type byte 21 might have set:

^ One or more of the sensors may be blocked by snow, mud, ice or debris. This might happen after going through a car wash in cold weather.

^ Silicone insulator surrounding sensor maybe missing, cut or twisted.

^ Improperly installed sensor, sensor maybe be crooked due to a tight wire harness.

^ One or more of the sensors may be scratched or the paint maybe chipped.

^ Excessive paint thickness on a sensor may cause an excessive sensor ring time. When replacing or refinishing a sensor, do not apply an

excessive amount of paint or clear coat.

Reference Information

Schematic Reference

Object Detection Schematics (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist Systems/Diagrams/Electrical

Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Object Detection Description and Operation (UVC) (See: Accessories and Optional Equipment/Collision Avoidance and Parking Assist

Systems/Description and Operation/Object Detection (UVC))Object Detection Description and Operation (UD5) (See: Accessories and Optional

Equipment/Collision Avoidance and Parking Assist Systems/Description and Operation/Object Detection Description and Operation (UD5))

Electrical Information Reference

^ Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

^ Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

^ Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

^ Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

2010 Cadillac Truck SRX AWD V6-3.0L Page 1032

2010 Cadillac Truck SRX AWD V6-3.0L Page 1032

Conditions for Setting the DTC

P0011 and P0021

The ECM detects the difference between the desired and actual camshaft position angle is greater than 5 degrees for greater 2.5 s.

P0014 and P0024

The ECM detects the difference between the desired and actual camshaft position angle is greater than 5 degrees for greater 10 s.

Action Taken When the DTC Sets

DTCs P0011, P0014, P0021, and P0024 are type B DTCs.

Conditions for Clearing the DTC

DTCs P0011, P0014, P0021, and P0024 are type B DTCs.

Diagnostic Aids

Inspect the engine for any recent engine mechanical repairs. An incorrectly installed camshaft, camshaft position actuator solenoid, mechanical

camshaft actuator, or timing chain can cause this DTC to set.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Camshaft Actuator System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Camshaft

Actuator System)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Note:

* The engine oil level and the oil pressure are critical to the correct operation of the camshaft position actuator system. Verify that the

engine has the correct oil level and the correct oil pressure before continuing with this diagnostic. Refer to Oil Pressure Diagnosis and

Testing (See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Component Tests and General Diagnostics/Oil Pressure

Diagnosis and Testing).

* The engine oil condition has a major impact on the camshaft actuator system. Debris in the oil can interfere with the camshaft position

actuator solenoid and the mechanical camshaft actuator operation. Inspect for dirty or degraded crankcase oil. The engine may require an

oil change. Inquire with the customer when the last oil change was performed. You may also monitor the scan tool Engine Oil Life

parameter. Advise the customer an oil change may be required.

* If a crankshaft or camshaft position sensor DTC is set, the Camshaft Position Actuator output control will not function.

1. Ignition ON, observe the scan tool DTC information. Verify that DTC P0016, P0017, P0018, P0019, P0335, P0336, P0338, P0340, P0341,

P0345, P0346, P0365, P0366, P0390, or P0391 is not set.

2010 Cadillac Truck SRX AWD V6-3.0L Page 853

2010 Cadillac Truck SRX AWD V6-3.0L Page 853

Conditions for Setting the DTC

C0595 02, C0600 02, and C0605 02

The signal voltage is less than 0.5 V for 1.5 s

C0595 05, C0600 05, and C0605 05

The signal voltage is greater than 4.5 V for 1.5 s

C0595 0A, C0600 0A, and C0605 0A

* The number of signal changes is less than specified value for 2.5 s.

* Vehicle speed is greater than 30 km/h (19 MPH)

Action Taken When the DTC Sets

* The electronic suspension control is disabled for the duration of the ignition cycle.

* The driver information center displays the SERVICE SUSPENSION SYSTEM message.

Conditions for Clearing the DTC

* A present DTC will clear on the next consecutive malfunction-free ignition cycle.

* A history DTC will clear after 41 consecutive malfunction-free ignition cycles.

Reference Information

Schematic Reference

Electronic Suspension Control Schematics (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Electronic Suspension Control Description and Operation (See: Steering and Suspension/Suspension/Suspension Control ( Automatic - Electronic

)/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool Vertical Body Acceleration parameters. The parameters should be 0 m/s(2).

Circuit/System Testing

1. Ignition ON, verify that DTC C0870 is not present.

瀚慖f the DTC is present, refer to DTC C0870 (See: C Code Charts/C0870) to diagnose that DTC prior to this diagnostic.

2. Ignition OFF, disconnect the harness connector at the appropriate B162 vertical body acceleration sensor.

3. Ignition OFF, open/close doors, and wait 60 seconds. Test for less than 5 ohm between the low reference circuit terminal 3 and ground.

瀚慖f greater than the specified value, test the low reference circuit for short to voltage or an open/high resistance. If the circuit tests normal,

replace the K19 suspension control module.

4. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 1 and ground.

2010 Cadillac Truck SRX AWD V6-3.0L Page 545

2010 Cadillac Truck SRX AWD V6-3.0L Page 545

Conditions for Setting the DTC

B2425 0D or B2430 0D

By measuring current and voltage output to the seat heating elements every 10 seconds, the rear seat heating control module calculates that the

heating element resistance is above the maximum resistance.

B2425 0B, B2425 0E, B2430 0B, or B2430 0E

By measuring current and voltage output to the seat heating elements every 10 seconds, the rear seat heating control module calculates that the

heating element resistance is below the minimum resistance.

Action Taken When the DTC Sets

The heated seat function for the affected seat will be disabled.

Conditions for Clearing the DTC

* The current DTC clears when the malfunction is no longer present, and the power mode changes to OFF then back to ACC or RUN.

* The history DTC will clear after 40 consecutive fault-free ignition cycles have occurred.

Reference Information

Schematic Reference

Heated/Cooled Seat Schematics (See: Body and Frame/Seats/Seat Temperature Element/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Rear Heated Seats Description and Operation (See: Body and Frame/Seats/Seat Temperature Element/Description and Operation/Rear Heated

Seats)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

B2425 0B, B2425 0D, or B2425 0E

1. Ignition OFF, disconnect the harness connector at the E14E seat back heating element.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

2. Test for 0.5 - 5 Ohms between terminal A and terminal B.

瀚慖f not within the specified range, replace the E14E seat back heating element.

3. Connect the harness connector at the E14E seat back heating element and disconnect the X2 harness connector at the K29R rear seat heating

control module.

Note: Element resistance must be measured twice to ensure that all failure conditions are simulated. First with the seat unoccupied, then with

the seat occupied.

4. Test for 1 - 7 Ohms between control circuit terminal 3 and control circuit terminal 1.

瀚慖f less than the specified range, test for a short between the control circuits. If the circuits test normal, replace the E14F seat cushion

2010 Cadillac Truck SRX AWD V6-3.0L Page 1003

2010 Cadillac Truck SRX AWD V6-3.0L Page 1003

Conditions for Setting the DTC

The ECM detects that the voltage on the fuel economy mode switch signal wire is in an indeterminate range.

Action Taken When the DTC Sets

DTC P15A1 is a Type B DTC.

Conditions for Clearing the MIL/DTC

DTC P15A1 is a Type B DTC.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

1. Verify that DTCs P159F and P15A0 are not set.

瀚慖f either or both of the DTCs are set, diagnose those DTCs first.

2. Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster is not illuminated.

3. Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster illuminates when the fuel economy mode switch

button is pressed.

4. Engine running, observe the DTC information with a scan tool. DTC P15A1 should not set.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: You must perform the Circuit/System Verification before proceeding with Circuit/System Testing.

1. Ignition OFF, disconnect the harness connector at the S87 Fuel Economy Mode switch.

Note: It may take up to 2 minutes for all vehicle systems to power down.

2. Ignition OFF, and all vehicle systems OFF, test for less than 5 ohm between ground circuit terminal 2 of the harness connector and ground.

瀚慖f greater than the specified value, test the ground circuit for an open/high resistance and repair as necessary.

3. Test for 266-294 ohm between 5 V reference voltage circuit terminal 9 and signal circuit terminal 10 of the S87 fuel economy mode switch.

瀚慖f not the specified range, replace the S87 fuel economy mode switch.

4. Test for 1,414-1,562 ohm between 5 V reference voltage circuit terminal 9 and ground circuit terminal 2 of the S87 fuel economy mode

2010 Cadillac Truck SRX AWD V6-3.0L Page 461

2010 Cadillac Truck SRX AWD V6-3.0L Page 461

Conditions for Setting the DTC

B0163 02 or B0163 05

The HVAC control module detects the sensor signal out of range. The signal voltage is less than 0.1 V or greater than 4.9 V for more than 50 ms.

B0183 02

The 5 V identification pulse is not received.

B0183 05

The input signal is static and greater than 4.8 V.

B1405 02

Clocked supply for multi zone sensor is shorted to ground.

B1405 05

Clocked supply for multi zone sensor is shorted to voltage or open.

Action Taken When the DTC Sets

* The system will use the last valid values as default.

* If no value is read at the time of fault, the HVAC Control Module uses 0 W/m(2) as intensity, 45掳 for elevation and -75掳 for azimuth.

Conditions for Clearing the DTC

B0163 02 or B0163 05

The sensor signal is within specified range between 0.1-4.9 V.

B0183 02

The 5 V identification pulse will be received.

B0183 05

The correct pulse signal succession will be received.

B1405 02 or B1405 05

The condition for setting the DTC is no longer present.

Reference Information

Schematic Reference

HVAC Schematics (See: Heating and Air Conditioning/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Automatic HVAC Description and Operation (See: Heating and Air Conditioning/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

2010 Cadillac Truck SRX AWD V6-3.0L Page 886

2010 Cadillac Truck SRX AWD V6-3.0L Page 886

Conditions for Setting the DTC

A supervised periodic message that includes the wheel speed serial data has not been received.

Action Taken When the DTC Sets

Specific subsystems will not function or operate in degraded mode.

Conditions for Clearing the DTC

A current DTC clears when the diagnostic runs and passes.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning)for scan tool information

Circuit/System Verification

Ignition ON, observe the scan tool EBCM Wheel Speed Sensor parameters. The reading should be the same speed on all sensors when driving in a

straight line at a speed greater than 20 km/h (13 MPH).

Circuit/System Testing

1. Ignition ON, verify that DTC C0035, C0040, C0045, or C0050 is not present in the EBCM.

瀚慖f any listed DTC is present, refer to DTC C0035, C0040, C0045, or C0050 (See: C Code Charts/C0035) to diagnose that DTC prior to

this diagnostic.

2. Replace the K17 Electronic Brake Control Module (EBCM) and verify the DTC does not reset.

瀚慖f the DTC resets, replace the module that set the DTC.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

Control Module References (See: Testing and Inspection/Programming and Relearning)for module replacement, setup and programming

C1210

DTC C1207-C1210, C1221-C1228, or C1232-C1235

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

2010 Cadillac Truck SRX AWD V6-3.0L Page 1424

2010 Cadillac Truck SRX AWD V6-3.0L Page 1424

Conditions for Setting the DTC

P0324

The ECM detects that the knock sensor signal indicates an excessive engine knock is present for greater than 10 s for at least 1 single cylinder.

P0325 and P0330

The ECM detects that the knock sensor signal circuits are open for greater than 10 s.

P0326 and P0331

* The ECM detects that the knock sensor signal indicates the sensor harness is connected, but the sensor is not properly bolted to the engine.

OR

* The ECM detects that the knock sensor signal indicates an excessive engine knock is present in an entire bank.

* Either of the above conditions exist for greater than 10 s.

P0327 and P0332

The ECM detects that the knock sensor signal circuits are shorted to ground for greater than 10 s.

P0328 and P0333

The ECM detects that the knock sensor signal circuits are shorted to voltage for greater than 10 s.

P06B6 and P06B7

The ECM has detected an internal knock sensor processor fault.

Action Taken When the DTC Sets

* DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0331, P0332 P0333, P06B6, and P06B7 are Type B DTCs.

* The ignition timing is retarded to reduce the potential of engine damaging spark knock.

Conditions for Clearing the DTC

DTCs P0324, P0325, P0326, P0327, P0328, P0330, P0331, P0332 P0333, P06B6, and P06B7 are Type B DTCs.

Diagnostic Aids

* Inspect the knock sensor for physical damage. A knock sensor that is dropped or damaged may cause a DTC to set.

* Inspect the knock sensor for proper installation. A knock sensor that is loose or over torqued may cause a DTC to set. The knock sensor

should be free of thread sealant.

* The knock sensor mounting surface should be free of burrs, casting flash, and foreign material.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

Electronic Ignition System Description (See: Powertrain Management/Computers and Control Systems/Description and Operation/Electronic

Ignition System Description)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

2010 Cadillac Truck SRX AWD V6-3.0L Page 794

2010 Cadillac Truck SRX AWD V6-3.0L Page 794

Conditions for Setting the DTC

C0186 5A

* The lateral acceleration sensor signal offset is out of specified range.

* The lateral acceleration sensor signal is not plausible with the yaw rate sensor signal, steering angle sensor signal and vehicle speed.

C0186 71

The EBCM received an invalid lateral acceleration sensor signal.

C0196 00

The yaw rate sensor signal is not plausible.

C0196 5A

* The yaw rate sensor offset is out of specified range.

* The yaw rate sensor signal is not plausible with the lateral acceleration sensor signal, steering angle sensor signal and vehicle speed.

C019B 5A

The yaw rate sensor signal is out of specified range.

C0287 4B

The longitudinal acceleration sensor signal offset is out of specified range.

C0287 5A

The longitudinal acceleration sensor signal is not plausible with the vehicle speed.

C0287 71

The EBCM received an invalid longitudinal acceleration sensor signal.

Action Taken When the DTC Sets

C0186 5A, C0186 71, C0196 00, C0196 5A, and C019B 5A

* The EBCM disables the stability control for the duration of the ignition cycle.

* The traction control/stability control-active indicator turns ON.

C0287 4B, C0287 5A, and C0287 71

The EBCM disables the hill start assist for the duration of the ignition cycle.

Conditions for Clearing the DTC

* A current DTC clears when the diagnostic runs and passes.

* The EBCM will turn OFF the indicator in the next ignition cycle.

Diagnostic Aids

DTC C0186 and C0287 may set after replacing the Multi-Axis Acceleration Sensor if the sensor is not configured and setup. Perform the

Multi-Axis Acceleration Sensor Module Programming and Setup (See: Brakes and Traction Control/Antilock Brakes / Traction Control

Systems/Yaw Rate Sensor/Testing and Inspection/Multi-Axis Acceleration Sensor Module Programming and Setup) and the Vehicle Yaw Sensor

Learn (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Yaw Rate Sensor/Testing and Inspection/Vehicle Yaw

Sensor Learn) procedures to complete the configuration and setup.

Reference Information

Schematic Reference

Antilock Brake System Schematics (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Diagrams/Electrical Diagrams)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Description and Operation

ABS Description and Operation (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Description and Operation)

Electrical Information Reference

2010 Cadillac Truck SRX AWD V6-3.0L Page 1182

2010 Cadillac Truck SRX AWD V6-3.0L Page 1182

Conditions for Setting the DTC

P0030, P0036, P0050, or P0056

The ECM detects that the commanded state of the driver and the actual state of the control circuit do not match for greater than 5 s.

P0053, P0054, P0059, or P0060

The ECM detects the HO2S heater is not within a specified resistance range at engine start-up.

P0135 or P0155

The ECM detects that the HO2S 1 heater current is greater than 3.1 amps, or less than 0.3 amps for greater than 8 s.

P0141 or P0161

The ECM detects that the HO2S 2 heater current is greater than 2.9 amps, or less than 0.3 amps for greater than 8 s.

Action Taken When the DTC Sets

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0030, P0036, P0050, P0053, P0054, P0056, P0059, P0060, P0135, P0141. P0155, and P0161 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics (LAU) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)Engine Controls Schematics

(LF1) (See: Diagrams/Electrical Diagrams/Powertrain Management/System Diagram)

Connector End View Reference

Component Connector End Views (See: Diagrams/Connector Views/Connector End Views By Name)

Electrical Information Reference

* Circuit Testing (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Circuit

Testing/Circuit Testing)

* Connector Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic

Procedures/Connector Repairs/Connector Repairs)

* Testing for Intermittent Conditions and Poor Connections (See: Testing and Inspection/Component Tests and General Diagnostics/General

Electrical Diagnostic Procedures/Circuit Testing/Testing for Intermittent Conditions and Poor Connections)

* Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical Diagnostic Procedures/Wiring

Repairs/Wiring Repairs)

* Heated Oxygen Sensor Wiring Repairs (See: Testing and Inspection/Component Tests and General Diagnostics/General Electrical

Diagnostic Procedures/Wiring Repairs/Heated Oxygen Sensor Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine idling, command the appropriate B52 HO2S heater ON and OFF with a scan tool while observing the B52 HO2S Heater Circuit Test

Status parameter. The parameter should display OK or Not Run.

2. Engine idling at operating temperature, observe the scan tool B52 HO2S Heater parameter. The amperage should be within 0.2-1.5 A.

3. Engine idling at operating temperature, move the related wiring and connectors while observing the B52 HO2S Heater parameter with a scan

tool. The parameter should not change with movement.

瀚慖f movement affects the parameter, repair the appropriate harness or connector.

4. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing