2010 Cadillac Truck SRX AWD V6-3.0L Page 1355

2010 Cadillac Truck SRX AWD V6-3.0L Page 1355

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-3.0L Page 948

2010 Cadillac Truck SRX AWD V6-3.0L Page 948

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect harness connector of the B47 fuel pressure sensor.

2. Ignition OFF, test for less than 1.0 ohm between the low reference circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K27

fuel pump control module.

3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 3 and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K27 fuel pump control module.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K27 fuel

pump control module.

4. If all circuits test normal, replace the B47 fuel pressure sensor.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Fuel Pressure Sensor Replacement - Fuel Feed Pipe (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pressure

Sensor/Switch/Service and Repair/Fuel Pressure Sensor Replacement - Fuel Feed Pipe)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for fuel pump control module replacement, setup,

and programming

P06B6

DTC P0324-P0328, P0330-P0333, P06B6, or P06B7 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0324

- Knock Sensor System Performance

DTC P0325

- Knock Sensor Circuit Bank 1

DTC P0326

- Knock Sensor Performance Bank 1

DTC P0327

- Knock Sensor Circuit Low Voltage Bank 1

DTC P0328

- Knock Sensor Circuit High Voltage Bank 1

DTC P0330

- Knock Sensor Circuit Bank 2

DTC P0331

- Knock Sensor Performance Bank 2

2010 Cadillac Truck SRX AWD V6-3.0L Page 1505

2010 Cadillac Truck SRX AWD V6-3.0L Page 1505

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Special Tools

J 41413-200 - Evaporative Emission System Tester (EEST)

Circuit/System Verification

1. Remove the fuel cap.

2. Ignition ON, engine OFF.

3. Observe the Fuel Tank Pressure Sensor parameter with a scan tool.

4. The Fuel Tank Pressure Sensor parameter should be 1.3-1.7 V.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the B150 fuel tank pressure sensor.

2. Ignition OFF, test for less than 5 ohm of resistance between the low reference circuit terminal 2 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

3. Ignition ON, test for 4.8-5.2V between the 5V reference circuit terminal 3 and ground.

瀚慖f less than the specified range, test the 5V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5V reference circuit for a short to voltage. If the circuit tests normal, replace the ECM.

4. Verify the scan tool B150 fuel tank pressure sensor parameter is less than 0.2V.

瀚慖f greater than the specified range, test the signal circuit terminal 1 for a short to voltage. If the circuit tests normal, replace the K20 ECM.

5. Install a 3A fused jumper wire between the signal circuit terminal 1 and the 5V reference circuit terminal 3. Verify the scan tool fuel tank

pressure sensor parameter is greater than 4.7V.

瀚慖f less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the

K20 ECM.

6. If all circuits test normal, test or replace the B150 fuel tank pressure sensor.

Repair Instructions

* Fuel Tank Pressure Sensor Replacement (See: Powertrain Management/Computers and Control Systems/Fuel Tank Pressure Sensor/Service

and Repair)

* For DTC P0452 or P0453, always perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic

procedure.

* For DTC P0451 or P0454, clear DTCs with a scan tool.

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0453

DTC P0451-P0454 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

* Diagnostic Procedure Instructions (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic Procedure

Instructions) provides an overview of each diagnostic category.

DTC Descriptors

DTC P0451

- Fuel Tank Pressure Sensor Performance

2010 Cadillac Truck SRX AWD V6-3.0L Page 1280

2010 Cadillac Truck SRX AWD V6-3.0L Page 1280

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1366

2010 Cadillac Truck SRX AWD V6-3.0L Page 1366

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1258

2010 Cadillac Truck SRX AWD V6-3.0L Page 1258

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool, DTC P0641 should not be set.

瀚慖f a DTC is set, refer to DTC P0641, P0651, P0697, or P06A3 (LF1) (See: P Code Charts/P0641/ECM).

2. Engine idling, observe the DTC information with a scan tool. DTC P0192 or P0193 should not set.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the multi-way harness connector X198 at the rear of the intake manifold.

2. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

Note: Testing for steps 3 through 7 is performed on the ECM side of the multi-way harness connector.

3. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal 5 and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20

ECM.

4. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 11 and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

6. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

7. Connect a 3 A fused jumper wire between the signal circuit terminal 12 and the 5 V reference circuit terminal 11. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground. If the circuit tests normal, replace

the K20 ECM.

8. Ignition OFF, remove the intake manifold.

9. Connect the multi-way harness connector X198.

Note: Testing for steps 12 through 16 are performed at the fuel rail fuel pressure sensor connector.

10. Disconnect the B47 fuel rail fuel pressure sensor connector.

11. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

12. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance.

13. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.

14. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage.

15. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

瀚慖f greater than the specified value, test the signal circuit for a short to voltage.

16. Connect a 3 A fused jumper wire between the signal circuit terminal B and the 5 V reference circuit terminal A. Verify the scan tool Fuel

Rail Pressure Sensor voltage parameter is greater than 4.96 V.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1344

2010 Cadillac Truck SRX AWD V6-3.0L Page 1344

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1425

2010 Cadillac Truck SRX AWD V6-3.0L Page 1425

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Engine at operating temperature, all accessories OFF, and engine speed greater than 2,000 RPM, observe the Knock Retard and Total Knock

Retard parameters. The parameters should be 0掳.

2. Engine idling, move the related harnesses and connectors for the KS circuits while observing the scan tool Knock Retard and Total Knock

Retard parameters. The parameters should remain steady with no abrupt changes.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note:

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using these diagnostic procedures.

* If an engine mechanical noise can be heard, repair the condition before proceeding with this diagnostic. Refer to Symptoms - Engine

Mechanical (See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related Diagnostic Procedures/Symptoms -

Engine Mechanical).

P0324, P0326 and P0331

1. Using a scan tool, verify DTCs P0335 or P0336 are not set.

瀚慖f any of the DTCs are set, diagnose them first. Refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Verify the following conditions do not exist.

* A loose or broken vehicle accessory

* A loose or broken accessory bracket

* Excessive engine mechanical noise

瀚慖f any of the conditions exist, repair as necessary.

3. Replace the K20 ECM if no external knock sensor circuit issues exist.

P0325, P0327, P0328, P0330, P0332, and P0333

1. Ignition OFF, disconnect the affected B68 KS.

2. Verify the affected B68 KS is properly tightened, refer to Fastener Tightening Specifications (See: Powertrain Management/Specifications).

3. Ignition OFF, with appropriate length jumper wires, connect the B68A KS1 harness to the B68B KS2 sensor and the B68B KS2 harness to

the B68A KS1 sensor.

4. Monitor the DTCs using a scan tool. Operate the vehicle within the conditions for running the DTC. Verify the fault does not follow the

sensor in question.

瀚慖f the fault follows the sensor in question, replace the appropriate B68 KS.

5. Ignition OFF, remove the jumper wires from the previous step.

6. Ignition ON, measure for 1-4 V between each of the following circuits and ground on the K20 ECM side of the harness connector:

* The B68 KS signal circuit, terminal A or 1

* The B68 KS signal circuit, terminal B or 2

瀚慖f less than the specified range, test the circuits for a short to ground or an open/high resistance. If the circuits test normal, replace the

K20 ECM.

瀚慖f greater than the specified range, test the circuits for a short to voltage. If the circuits test normal, replace the K20 ECM.

7. Test for intermittent or poor connections at the ECM, B68 KS, and in-line connectors where present.

8. If all circuits test normal, replace the K20 ECM.

P06B6 or P06B7

1. Using a scan tool, verify the following DTCs are not set: P0325, P0327, P0328, P0330, P0332, and P0333.

瀚慖f any of the DTCs are set, diagnose them first.

2. DTCs P06B6 and P06B7 indicate an internal ECM circuitry failure. Verify the external knock sensor circuits and connectors for proper

2010 Cadillac Truck SRX AWD V6-3.0L Page 1190

2010 Cadillac Truck SRX AWD V6-3.0L Page 1190

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify no B52 HO2S heater DTCs are set.

瀚慖f a B52 HO2S heater DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code

Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).

2. Engine running, observe the appropriate scan tool B52 HO2S voltage parameter. The reading should be within the range of 50-1,050 mV.

3. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate B52 HO2S harness connector.

2. Ignition ON, observe the appropriate scan tool HO2S voltage parameter. The parameter should display 1.27 V.

瀚慖f less than the specified range, test the high and low signal circuits for a short to ground. If both signal circuit test normal, replace the

K20 ECM.

3. Ignition ON, test for 2.5-3.0 V between the high signal circuit terminal B and ground.

瀚慖f less than the specified range, test the high signal circuit for an open/high resistance. If the circuit tests normal, replace the K20 ECM.

瀚慖f greater than the specified range, test the high signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Ignition OFF, connect a 3 A fused jumper wire between the high signal circuit terminal B and the low signal circuit terminal A.

Note: The low signal circuit is tied to a pull-up circuit within the ECM. A voltage of 0.90-1.10 V on the low signal circuit is normal.

5. Ignition ON, verify the scan tool HO2S parameter displays 0.0 V.

瀚慖f greater than the specified range, test the low signal circuit for an open/high resistance or for a short to voltage. If the circuit tests

normal, replace the K20 ECM.

6. If all circuits test normal, test or replace the appropriate B52 HO2S.

Repair Instructions

Caution: Refer to Heated Oxygen Sensor Resistance Learn Reset Caution (See: Powertrain Management/Computers and Control

Systems/Oxygen Sensor/Service Precautions/Heated Oxygen Sensor Resistance Learn Reset Caution).

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 1 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 1 Sensor 2)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 1 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 1)

* Heated Oxygen Sensor Replacement - Bank 2 Sensor 2 (LF1) (See: Powertrain Management/Computers and Control Systems/Oxygen

Sensor/Service and Repair/Heated Oxygen Sensor Replacement - Bank 2 Sensor 2)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, setup, and programming

P0138

DTC P0131, P0132, P0137, P0138, P0151, P0152, P0157, P0158, P2A00, P2A01, P2A03, or P2A04 (LF1)

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Diagnostic System

Check - Vehicle) prior to using this diagnostic procedure.

* Review Strategy Based Diagnosis (See: Testing and Inspection/Initial Inspection and Diagnostic Overview/Strategy Based Diagnosis) for an

overview of the diagnostic approach.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1269

2010 Cadillac Truck SRX AWD V6-3.0L Page 1269

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

2010 Cadillac Truck SRX AWD V6-3.0L Page 1377

2010 Cadillac Truck SRX AWD V6-3.0L Page 1377

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0685 or P1682 should not set.

瀚慖f a DTC is set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Engine operating, observe the DTC information with a scan tool. DTC P0201, P0202, P0203, P0204, P0205, P0206, P0261, P0262, P0264,

P0265, P0267, P0268, P0270, P0271, P0273, P0274, P0276, or P0277 should not set.

3. Observe the scan tool Current Misfire Counter parameters. The Current Misfire Counters should not increment.

4. Ignition ON, observe the scan tool Cylinder 1-6 Injector Control Circuit Status parameters. Verify the Injector Control Circuit Status

parameters display OK.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the appropriate multi-way harness connector X198 or X199, at the rear of the intake manifold.

2. Ignition ON, observe the appropriate scan tool Cylinder 1-6 Injector Control Circuit Status. The parameter should display Open.

瀚慖f not the specified value, test the appropriate high voltage supply circuit, ECM side, for a short to ground or the appropriate high voltage

control circuit, ECM side, for a short to voltage. If the circuits test normal, replace the K20 ECM.

3. Ignition ON, connect a test lamp between the appropriate high voltage supply circuit and the high voltage control circuit. The Injector

Control Circuit Status should transition from Open to OK.

瀚慖f not the specified value, test for the following conditions in the ECM side of the harness:

* An open/high resistance in the high voltage supply circuit

* An open/high resistance in the high voltage control circuit

* A short to ground in the high voltage control circuit

* A short to voltage in the high voltage supply circuit

瀚慖f the circuits test normal, replace the K20 ECM.

Note: Testing for the following steps is performed on the fuel injector side of the multi-way harness connector. It may be necessary to

remove the intake manifold to isolate the condition.

4. Ignition OFF, measure the resistance between the appropriate high voltage supply circuit and ground. The DMM should display OL ohm.

瀚慖f less than the specified range, test the high voltage supply circuit and the high voltage control circuit for a short to ground. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

5. Test for 2-3 ohm between the appropriate high voltage supply circuit and high voltage control circuit.

瀚慖f less than the specified range, test for a short between the high voltage supply circuit and high voltage control circuit. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector(s).

瀚慖f greater than the specified range, test the high voltage supply circuit and high voltage control circuit for an open/high resistance. If the

circuits/connections test normal, test or replace the appropriate Q17 fuel injector.

Component Testing

* Fuel Injector Solenoid Coil Test (LAU) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and Inspection

)Fuel Injector Solenoid Coil Test (LF1, LFW) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Injector/Testing and

Inspection)

* Fuel Injector Balance Test (LAU) (See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Component Tests

and General Diagnostics/Fuel Injector Balance Test)Fuel Injector Balance Test (LF1, LFW) (See: Powertrain Management/Computers and

Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Injector Balance Test)

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.