2010 Cadillac Truck SRX AWD V6-3.0L Page 1078

-

2010 Cadillac Truck SRX AWD V6-3.0L Page 1078



DTC Descriptors



DTC P0030



- HO2S Heater Control Circuit Bank 1 Sensor 1



DTC P0036



- HO2S Heater Control Circuit Bank 1 Sensor 2



DTC P0050



- HO2S Heater Control Circuit Bank 2 Sensor 1



DTC P0053



- HO2S Heater Resistance Bank 1 Sensor 1



DTC P0054



- HO2S Heater Resistance Bank 1 Sensor 2



DTC P0056



- HO2S Heater Control Circuit Bank 2 Sensor 2



DTC P0059



- HO2S Heater Resistance Bank 2 Sensor 1



DTC P0060



- HO2S Heater Resistance Bank 2 Sensor 2



DTC P0135



- HO2S Heater Performance Bank 1 Sensor 1



DTC P0141



- HO2S Heater Performance Bank 1 Sensor 2



DTC P0155



- HO2S Heater Performance Bank 2 Sensor 1



DTC P0161



- HO2S Heater Performance Bank 2 Sensor 2



Diagnostic Fault Information



Typical Scan Tool Data

Comments

Post a Comment

Popular posts from this blog

2010 Cadillac Truck SRX AWD V6-3.0L Page 792

-
2010 Cadillac Truck SRX AWD V6-3.0L Page 792 The body control module (BCM) monitors the brake pedal position sensor and sends a serial data message when the brake pedal is applied. When the vehicle is stopping, the electronic brake control module (EBCM) monitors for the brake pedal applied serial data message from the BCM, with the brake pressure increasing and the vehicle slowing down, or when the vehicle is accelerating, the brake pedal is not applied and brake pressure is not increasing. Conditions for Running the DTC Ignition ON. Conditions for Setting the DTC * The EBCM detects 4 accelerations from standstill to a vehicle speed greater 40 km/h (26 MPH) without any brake light switch signal changes. * The EBCM detects the vehicle speed is greater than 20 km/h (13 MPH), the brake pedal is applied for 360 s, and brake pressure is less than 15 bar (218 PSI). Conditions for Clearing the DTC A current DTC clears when the diagnostic runs and passes. Action Taken When the DTC Sets No acti...
Read more

2010 Cadillac Truck SRX AWD V6-3.0L Page 476

-
2010 Cadillac Truck SRX AWD V6-3.0L Page 476 Circuit/System Testing 1. Ignition OFF, disconnect the harness connectors X1, X2, X4, X5, and X6 at the K9 BCM. 2. Ignition OFF, test for less than 3.0 Ohms between the ground circuit terminals listed below and ground: * Terminal 1 X1 * Terminal 2 X2 瀚慖f not within the specified range, test the ground circuit for an open/high resistance. 3. Ignition ON, verify a test lamp illuminates between the B+ circuit terminals listed below and ground: * Terminal 2 X1 * Terminal 3 X1 * Terminal 4 X1 * Terminal 1 X2 * Terminal 3 X2 * Terminal 4 X2 * Terminal 20 X4 * Terminal 3 X5 * Terminal 4 X5 瀚慖f the test lamp does not illuminate, test the B+ circuits for a short to ground or an open/high resistance. 4. If all the circuits test normal, test or replace the K9 BCM. Repair Instructions Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure. Control Module References (See: Testing and Inspection/Prog...
Read more

2020 Ford Explorer ST: First Impressions – Cars.com

-
Image
BMW Diagnostic and Repair Information ,Wiring Diagrams. DTC. TSB. Types: TSB, DTC, Wiring Diagrams, OEM Procedures. Trusted by more than 400,000 technicians. OEM accurate fix for faster repairs. Repair Procedures and Labor Times. Factory Auto Repair info. Request A Demo Today. Factory-Correct Diagrams. Factory Part Numbers. Maintenance Schedules. Repair Procedures. Labor Times. Types: TSB, DTC.car insurance, auto insurance, auto, car, vehicle, insurance, quote, quotes, online, insurance，auto, autos, car, cars, vehicle, vehicles, used car, pre-owned car, pre-owned vehicle, used auto, used vehicle, rental，auto racing news, car racing news
Read more