2010 Cadillac Truck SRX AWD V6-3.0L Page 1253

-

2010 Cadillac Truck SRX AWD V6-3.0L Page 1253



Scan Tool Reference



Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information



Circuit/System Verification



1. Observe the scan tool DTC information, verify DTC P0627, P0628, P0629, P069E or U0109 is not set.



瀚慖f any of the DTCs are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code



Descriptions/Diagnostic Trouble Code (DTC) List - Vehicle).



2. Engine idling, observe the scan tool Fuel Rail Pressure Sensor parameter. The pressure should be approximately 1.9-2.1 Mpa (279-305 psi).



3. Engine idling, the scan tool Fuel Rail Pressure Sensor should be close to the scan tool Desired Fuel Rail Pressure. As the engine speed



increases, the Desired Fuel Rail Pressure and the Fuel Rail Pressure Sensor should closely match each other.



4. Move related harnesses/connectors of the B47 fuel rail fuel pressure sensor and verify the engine does not stumble, stall, or change engine



speed.



瀚慖f the engine stumbles, stalls, or changes engine speed, test or repair the suspected harness or connection.



5. Observe the DTC information with a scan tool, DTC P0191 should not set.



6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the



conditions that you observed from the Freeze Frame/Failure Records data.



Circuit/System Testing



1. Ignition OFF, disconnect the multi-way harness connector X198 at the rear of the intake manifold.



2. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



Note: Testing for steps 3 through 7 is performed on the ECM side of the multi-way harness connector.



3. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal 5 and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the K20



ECM.



4. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



5. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal 11 and ground.



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance. If the circuit tests normal,



replace the K20 ECM.



瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.



6. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.



瀚慖f greater than the specified value, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.



7. Connect a 3 A fused jumper wire between the signal circuit terminal 12 and the 5 V reference circuit terminal 11. Verify the scan tool Fuel



Rail Pressure Sensor Voltage parameter is greater than 4.96 V.



瀚慖f less than the specified value, test the signal circuit for an open/high resistance or a short to ground. If the circuit tests normal, replace



the K20 ECM.



8. Ignition OFF, remove the intake manifold.



9. Connect the multi-way harness connector X198.



Note: Testing for steps 12 through 16 are performed at the fuel rail fuel pressure sensor connector.



10. Disconnect the B47 fuel rail fuel pressure sensor connector.



11. Remove the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



12. Ignition OFF, test for less than 5 ohm between the low reference circuit terminal C and ground.



瀚慖f greater than the specified range, test the low reference circuit for an open/high resistance.



13. Install the fuse that supplies B+ to terminal 52-X1 of the K20 ECM.



14. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal A and ground.



瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or an open/high resistance.



瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage.



15. Ignition ON, verify the scan tool Fuel Rail Pressure Sensor voltage parameter is less than 0.02 V.

Comments

Post a Comment

Popular posts from this blog

2010 Cadillac Truck SRX AWD V6-3.0L Page 968

-
2010 Cadillac Truck SRX AWD V6-3.0L Page 968 P013A P013C, P013E, or P014A * Before the ECM can report DTC P013A, or P013C failed, DTCs P013E, P014A, P2270, and P2272 must run and pass. * Before the ECM can report DTC P013E, or P014A failed, DTCs P2270 and P2272 must run and pass. * DTCs P0030, P0036, P0053, P0054, P0101, P0102, P0103, P0106, P0107, P0108, P0120, P0121, P0122, P0123, P0131, P0132, P0133, P0134, P0135, P0137, P0138, P013A, P013B, P013E, P013F, P0140, P0141, P0171, P0172, P0201, P0202, P0203, P0204, P0220, P0222, P0223, P0300, P0442, P0443, P0446, P0449, P0455, P0496, P1133, P1174, P1516, P2101, P2119, P2135, P2176, P2270, P2271, P2A00 are not set. * The ignition 1 voltage is between 10-32 V. * The learned heater resistance is valid. * The fuel level is greater than 10 %. * The engine run time is equal to or greater than 5 min. * The accelerator pedal (APP) is steady. * The torque converter clutch (TCC) is applied. * The DTCs run once per ignition cycle, during decel fuel
Read more

With Respect To The C63 AMG

-
Normal equipment in the new C-Class is a 100-watt Audio 20 system. Along with its eight speakers, the Audio 20 includes a single CD slot, telephone keypad, a MP3 plug in the glove box and a Bluetooth interface. The diesel lineup features a 136-hp E200 CDI, a 170-hp E220 CDI, a 204-hp E250 CDI and the 3.0L liter 231-hp E350 CDI. The latest C-Class shines on the type of roads that would have left it lagging behind older generations of 3-Sequence and A4. The Audi A4 is a better purchase than the C-Class. And in addition the analog consequence is best as a result of we might regulate the facility of the impact by hand. Never bounce whereas in an exceedingly stretch as this may occasionally result in harm! In response to a simple equation the grip is a result of the material's friction coefficient occasions the utilized pressure. The load-lugging Three was once offered in Thailand at 4.099 million baht in 320d M Sport trim. Then add 2 million Individuals are carnivorous animals that nee
Read more

Disclaimer2020 Lincoln Truck MKT FWD V6-3.7L Technical Service Bulletin # 10-6-3 Date: 100412

-
Disclaimer2020 Lincoln Truck MKT FWD V6-3.7L Technical Service Bulletin # 10-6-3 Date: 100412 Navigation Radio - Various Navigation/Audio Concerns TSB 10-6-3 2020 Lincoln Truck MKT FWD V6-3.7L  Page 22 04/12/10 SIRIUS RADIO AND NEXT GENERATION NAVIGATION CONCERNS - BUILT BEFORE 3/8/2010 FORD: 2010 Fusion, Mustang, Taurus 2009-2010 E-Series, Edge, Escape, Expedition, Explorer Sport Trac, Explorer, F-150, F-Super Duty, Flex LINCOLN: 2009-2010 MKS 2010 MKZ 2009-2010 MKX, Navigator 2010 MKT MERCURY: 2010 Milan 2009-2010 Mariner, Mountaineer ISSUE Some 2009-2010 vehicles built on or before 3/8/2010 and equipped with Sirius Radio with Navigation, may exhibit repeated traffic incident warnings every 2 minutes in some areas, VIN number displayed in the Navigation system does not match the vehicle's VIN, Juke box can not delete or shuffle songs and the MKZ (without THX(R)) speakers fade incorrectly. ACTION Follow the Service Procedure to correct the condition. SER
Read more