2010 Cadillac Truck SRX AWD V6-3.0L Page 1150

2010 Cadillac Truck SRX AWD V6-3.0L Page 1150

Repairs/Wiring Repairs)

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Ignition ON, observe the DTC information with a scan tool. Verify DTC P06A3 is not set.

瀚慖f the DTC is set, refer to DTC P0641, P0651, P0697, or P06A3 (LF1) (See: P Code Charts/P0641/ECM).

2. Ignition ON, observe both Throttle Position Sensor voltage parameters with a scan tool. Verify the scan tool Throttle Position Sensor 1 and 2

parameters are between 1.0-4.0 V.

3. Perform the scan tool Throttle Sweep Test while observing the Throttle Position Sensors 1 and 2 Agree/Disagree parameter. The parameter

should display Agree.

4. Observe the DTC Information with a scan tool. DTCs P0121, P0122, P0123, P0222, P0223, and P2135 should not set.

5. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the Q38 throttle body assembly.

2. Ignition OFF and all vehicle systems OFF. It may take up to 2 minutes for all vehicle systems to power down. Test for less than 5 ohm

between the low reference circuit terminal C and ground.

瀚慖f greater than the specified range, test the low reference circuit for a short to voltage, or an open/high resistance. If the circuit tests

normal, replace the K20 ECM.

3. Ignition ON, test for 4.8-5.2 V between the 5 V reference circuit terminal E and ground.

瀚慖f less than the specified range, test the 5 V reference circuit for a short to ground or open/high resistance. If the circuit tests normal,

replace the K20 ECM.

瀚慖f greater than the specified range, test the 5 V reference circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

4. Test for less than 1 V between the TP sensor 1 signal circuit terminal D and ground.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

5. Test for 4.8-5.2 V between the TP sensor 2 signal circuit terminal F and ground.

瀚慖f less than specified range, test the signal circuit for a short to ground, or an open/high resistance. If the circuit tests normal, replace the

K20 ECM.

瀚慖f greater than specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K20 ECM.

6. Install a 3 A fused jumper wire between TP sensor 1 signal circuit terminal D and the 5 V reference circuit terminal E. Verify the scan tool

TP sensor 1 voltage parameter is greater than 4.8 V.

瀚慖f less than the specified range, test the signal circuit for a short to ground, or an open/high resistance. If the circuit tests normal, replace

the K20 ECM.

7. If all circuits test normal, test or replace the Q38 throttle body assembly.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the repair.

* Throttle Body Assembly Replacement (LF1) (See: Powertrain Management/Fuel Delivery and Air Induction/Throttle Body/Service and

Repair/Removal and Replacement)Throttle Body Assembly Replacement (LAU) (See: Powertrain Management/Fuel Delivery and Air

Induction/Throttle Body/Service and Repair/Removal and Replacement)

* Control Module References (See: Testing and Inspection/Programming and Relearning) for ECM replacement, programming, and setup

P0123

DTC P0121-P0123, P0222, P0223, or P2135 (LF1, LFW)