2010 Cadillac Truck SRX AWD V6-3.0L Page 1314

2010 Cadillac Truck SRX AWD V6-3.0L Page 1314

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions (See: Diagnostic Trouble Code Descriptions/Powertrain Diagnostic Trouble Code

(DTC) Type Definitions)

Scan Tool Reference

Control Module References (See: Testing and Inspection/Programming and Relearning) for scan tool information

Circuit/System Verification

1. Observe the DTC information with a scan tool. DTC P0627, P0628, P0629, P069E, or U0109 should not set.

瀚慖f a DTC is set refer to Diagnostic Trouble Code (DTC) List - Vehicle (See: Diagnostic Trouble Code Descriptions/Diagnostic Trouble

Code (DTC) List - Vehicle).

2. Attempt to start and idle the engine.

3. Observe the DTC information with a scan tool. DTCs P0089, P00C6, P228C, and P228D should not set.

4. Engine idling, observe the Fuel Rail Pressure Sensor parameter with a scan tool. The pressure should be approximately 1.9-2.1 Mpa (279-305

psi).

5. Command an increase and decrease in Fuel Pressure with a scan tool. Observe the scan tool Fuel Rail Pressure Sensor parameter. The Fuel

Rail Pressure Sensor parameter should increase or decrease with each commanded state.

6. Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the

conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

Note: Circuit/System Verification must be performed first or misdiagnosis may result.

1. Ignition ON, observe the scan tool Fuel Pump Control Module Fuel Pressure Sensor parameter. Command an increase in Fuel Pressure with a

scan tool. Verify the Fuel Pressure Sensor parameter increases to greater than 414 kPa (60 psi) as commanded.

瀚慖f less than the specified range, refer to Fuel System Diagnosis (LF1 China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (China))Fuel System Diagnosis (LF1 Except China) (See:

Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China))Fuel

System Diagnosis (LAU China) (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pump/Testing and Inspection/Fuel

System Diagnosis (China))Fuel System Diagnosis (LAU Except China) (See: Powertrain Management/Fuel Delivery and Air

Induction/Fuel Pump/Testing and Inspection/Fuel System Diagnosis (Except China)).

Note: As little as 2 ohm on either circuit of the high pressure fuel pump actuator will cause these DTCs to set. Test the circuits of the high

pressure fuel pump actuator for a high resistance if you suspect a condition.

2. Remove the G18 high pressure fuel pump and visually inspect the lobes on the camshaft for unusual wear.

瀚慖f the lobes appear normal, replace the G18 high pressure fuel pump.

瀚慖f the lobes are worn, replace the camshaft.

Component Testing

Static Test

1. Ignition OFF, disconnect the harness connector at the G18 high pressure fuel pump.

Note: The DMM and test leads must be calibrated to 0 ohm in order to prevent misdiagnosis.

2. Test for 10 ohm plus/minus 1 ohm at 25掳C (77掳F) between the low control circuit terminal 1 and the high control circuit terminal 2.

瀚慖f not within the specified range, replace the G18 high pressure fuel pump.

3. Test for infinite resistance between each terminal and the G18 high pressure fuel pump housing.

瀚慖f not the specified value, replace the G18 high pressure fuel pump.

Repair Instructions

Perform the Diagnostic Repair Verification (See: Verification Tests) after completing the diagnostic procedure.

* Camshaft Replacement - Right Side (See: Engine, Cooling and Exhaust/Engine/Camshaft, Lifters and Push Rods/Camshaft/Service and

Repair/Camshaft Replacement - Right Side)

* Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail (See: Powertrain Management/Fuel Delivery and Air Induction/Fuel Pressure

Sensor/Switch/Service and Repair/Fuel Pressure Sensor Replacement - Fuel Injection Fuel Rail)